How to Fillet a Flat Fish

How to Fillet a Flat Fish

http://ift.tt/2rqEtqF

how to fillet a flat fishPhoto by Hank Shaw

Here is how I fillet a flat fish. When I say “flat fish,” I mean halibut, fluke, flounder, sole, plaice, turbot, etc. This method works with any flat fish, with the exception of really small ones like sand dabs.

I generally use this procedure with flat fish larger than about a pound, up to about 40 pounds. The larger the fish, the more extras like collars or cheeks you can collect; they’re not really worth it on fish smaller than about 10 pounds. Really large Pacific and Atlantic halibut are, more or less, cut this way, too, but are then steaked.

Start by getting a lightning sharp fillet knife appropriate to your fish. I tend to use a Kershaw fillet knife with at least a 9-inch blade. You want a long blade with a larger fish so you can make long, sweeping strokes. This results in a cleaner fillet.

You fillet a flat fish with the intention of getting four boneless fillets, not two like in round fish. How to do this? Easy, as the fish itself gives you directions. First, lay it out on a work surface and look for the lateral line running down the center of the fish. It follows the spine of the fish.

Slice down to the spine along this line, from right behind the pectoral fin down to the tail. Then you want to make three cross cuts that will mark the ends of your fillets. First is across the tail, and the other two are from the pectoral fin to the vent, and from the pectoral fin to right behind the head. Like this:

filleting a halibutPhoto by Hank Shaw

Now, starting at the tail, use your knife to free one half from the skeleton. Run the knife along the spine in long, gentle strokes. At first you just want to get the fillet off the spine, then, again starting at the tail end, sweep the knife against the ribs toward the line of fins at the edge of the fish. You want to have the knife touching the ribs. When you get to the tail part, run the knife all the way to the edge so you get what I call the “frill” meat; more on that in a bit.

Photo by Hank Shaw

When you have one fillet off, the second comes much easier. Take your time at first, but once you get the hang of it, you can cut even a large flat fish, like this 20-pound California halibut, in a few minutes.

With both halves off the top, repeat the process on the white side of the fish. The top fillets are always thicker, and if you are nervous about filleting, you might want to start with the white side, as there is less meat there to mess up. I generally start at the top, though, as I’ve been doing this for many years.

When you have all four fillets off the carcass should look like this:

filleted halibutPhoto by Hank Shaw

If you’ve not been that clean, fear not: Just slice any remaining meat off the carcass and flash freeze it overnight, to kill any potential parasites. Then, eat it as sashimi with some wasabi and soy.

In general, the skin on a larger flat fish isn’t terribly good to eat. They have very small scales that don’t come off easily, and the skin is pretty thick. I do like the skin on small flat fish, though, like sand dabs and little flounder. So, for the most part, you want skinless fillets.

To do this, you again need that long knife. A short one make skinning much harder. I start from the tail end — the tail meat is, in my opinion, not as good as the meat behind the head. Slice down to the skin and anchor the back of the skin with your off hand. Slide the knife between the skin and fillet and work the skin back to you. On a big fish, you will need to readjust your grip once or twice.

Photo by Hank Shaw

The skin comes off surprisingly easily. If you’ve cut too much meat off, slice it thin and add it to the sashimi pile. If you left some skin on the fillet, carefully slice it off. This is where a truly sharp knife comes in handy.

Now, many times you will still have the “frill” meat attached to the fillet. This needs to go, as it will fall off the main fillet when you cook it. You can usually just pull it off. Save it for the sashimi pile, as this is the most sought-after cut in all of sushi, at least when it comes to flat fish. The Japanese call it engawa.

Photo by Hank Shaw

Again, be sure to flash freeze your halibut, fluke, flounder, etc meat that you intend on eating raw, to kill any potential parasites.

From here, you’re done with smaller flat fish. For larger ones, you will want to cut the long fillets into three kinds of meat. First is the loin, the thickest part of the fillet. Square off the head end of the fillet and use what you cut off for soups, Hawaiian poke, halibut curry or somesuch. Do the same with the bottom end of the loin, where it’s much thinner than the primo parts.

You then cut the loin into pretty blocks you will want to sear; I especially like them brined and served with an Italian salsa verde. Finally, when you get toward the tail end, you either add it to the soup pile, or keep them separate for making fish and chips.

That leaves the cheeks and the collars.

Cheeks you just remove using your ingenuity; there’s no particular way to get them out. Simply poke your knife through the skin, then slide it under the skin to remove. Then slice away the cheek. Only tip I can give you is that it is deeper near the eye than near the gill plate. These are best floured and fried.

Finally, on really large flat fish, you have the collars. I only bother with these when the fish is about 10 pounds or larger. Halibut collars are best marinated and grilled, using this recipe.

Photo by Hank Shaw

To remove them, I use kitchen shears to cut them free from right behind the pectoral fin. Then I use my knife to slice down to the edge and cut the collar in half. Alternatively, you can remove halibut throats by snipping the whole collar off under the chin, then at each gill plate. You then snap it flat and you have both collars as one piece.

Some people eat the roe and the livers, but I rarely do. If you look closely at the liver in the picture above, you will see liver flukes, which are parasites. Not good eats.

So there you have it: A tutorial on how to get every bit of edible meat from a flat fish. I’ve been doing it this way for many years, but I am betting some of you have different methods. Let me know in the comments!

Photo by Hank Shaw

Hunting

via Hunter Angler Gardener Cook http://honest-food.net

June 14, 2017 at 08:01AM

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s